+91 (40) 6733-0000
Vidhatasri Sponge Iron (India) Pvt. Ltd. was taken over as a sick unit and reinstated to operating condition under the name MPL Cement & Sponge Pvt.Ltd. in the year 2008.The company has a 30TPD rotary kiln with pre-heater technology to manufacture Direct Reduced Iron (DRI) and a 200 TPD cement grinding unit. The company sells its cement under the flagship brand MPL. MPL has connected with various customers in Andhra Pradesh with a Strong dealer network which is ever increasing. Soon we will be foraying into entire south India.
Bottom cup every 500mm centre to centre, 48.3OD Dia medium B Class round pipe, Malleable cast iron top cup CO2 MIG welded.
Uses: Standard/vertical is generallyusing in scaffolding work and also act as a base structure for Formwork strengthening.
The Ledgers are manufactured from 48.3OD Día medium B Class round pipe, CO2 MIG welded. tube with forged steel blade ends, which locate into bottom cups of the standards and are locked in place by the corresponding top cups.
Uses: The load carrying capacity of the scaffold will be significantly reduced where it is not possible to place the first ledger at the base of the standards.
Tube and fitting ledgers should be joined with sleeve couplings positioned no more then one third of the bay length from a standard and staggered on alternative lifts.
32, 36 & 38 OD solid round, hydraulic rolled threaded rod, malleable CI nut, CO2MIG welded, base plate of size150x150x6 mm.
Adjustable Prop with NB 50 mm pipe as outer, NB 40 mm pipe as iner slider, 150x150x6 mm MS Plate as Base Plate,Malleable CI nut, dipped Berger paint.
Made of 2mm HR sheet, 10mm round and CO2 MIG welded.
32, 36 & 38 OD Solid round, hydraulic rolled threaded; malleable CI nut, CO2 MIG welded, U Head of size 100*100*150*6mm.
Uses: It is used in conjunction with Fork heads, Socket Base and Drophead Adaptors.
The Screw Jack provides a method of jacking which can be used at either the top or bottom of a scaffold structure.
Made of 25*25*mm square tube 2.00mm thick and 300 mm width,co2 MIGwelded.
Spigot Pin is a part of cup lock systems. It is made from 250/300 long pipes of 38-39 MM OD & the Washer is welded at the center of spigot.
Uses: It is for connecting cup lock standards vertical. scaffolding Props have outer as well as inner membranes manufactured using medium class pipe.
Clampsare devices used to connect two tubes, clamps are used in conjunction with systems scaffolds mainly for the attachment of ties, plan bracing and cross bracing. The proper use of appropriate clamps is therefore important to the stability of scaffold.
For use on vertical/Jack and also props. Locking plate when turned allows seating plate to drop through slot by 80mm. height for easy removal of beams and floor form/plywood on infill beams safe load 40KN
Available in Multiple sizes according to various standard or vertical spacing of 2.5, 1.9 & 1.25 M.c/c. Decks and infill beams are interchangeable, and their top flanges provide stepped seating 35-40mm. Floor form or infill beams are suitable with the top surface in level with concrete and acting as deck shuttering. Loads distributed safely on deck beams in 40 KN
Available in Multiple sizes according to various standard or vertical spacing of 2.5, 1.9 & 1.25 M.c/c. Decks and infill beams are interchangeable, and their top flanges provide stepped seating 35-40mm. Floor form or infill beams are suitable with the top surface in level with concrete and acting as deck shuttering. Loads distributed safely on deck beams in 40 KN.
Safe axial load table on verticals (KN)
Vertical distance between ledgers
The load is based on IS: 806 – 1968. 1KN=101.97Kgs.